|
|
|
Group 1: Data Acquisation
|
|
40xxx
|
|
|
|
|
ProduktName
|
| Type-No.: 1024.0000
Measuring Converter for analog signal processing
| Data aquisition: |
4 analog, 3 digital inputs |
| Data output: |
4 analog, 1 digital output, connection for 3 – coil receiver (selsyn motor system),
3 serial interfaces
|
| Power supply: |
24 VDC, isolated |
| Construction: |
Euro card contained in Aluminium housing
|
| Dimensions: |
165 x 105 x 30 mm |
| Weight: |
ca. 350 g |
Type-No.: 1024.1000
Custom Specific Configuration
of the measuring converter for analog signal processing
Type-No.: 1032.0000
Configuration- and Evaluation Software for precipitation datalogger
(refer to group 7, type 7041)
Type-No.: 1032.1000
RS232 Interface Cable for data read-out
(refer to group 7, type 7041)
Type-No.: 1110.0000
Universal Measuring Converter
for analog signal processing
| Data acquisition: |
1 analog and 1 digital Input,
for alternative connection of sensors for wind speed, wind direction, temperature, rel. humidity, air pressure, solar radiation as well as precipitation
|
| Data output: |
2 analog outputs for instantaneous and
average value 0/4 ...20 mA
|
| Accuracy: |
± 0.1 % basing on FS |
| Power supply: |
10...30 VDC, isolated |
Size:
|
Euro card incl. Connector |
| Dimensions: |
168 x 100 x 35 mm |
| Weight: |
approx. 50 g |
| |
All setups by software. |
|
Zoom | Type-No.: 1130.0000
Radiation Measuring Converter
| Input: |
-8...+24 mV or 0...32 mV (selectable) |
Output:
|
4...20 mA
(simultaneously for supply)
|
Operating temp.:
|
-40°C ...+80°C |
Housing:
|
Aluminium, 64 x 58 x 34 mm, IP 65 |
|
Zoom | Type-No.: 1040.1000
Intelligent Sensor Module, ISM 111
Multi-channel module with 4 analog inputs suitable for measuring current, voltage and resistance (also for thermocouples, PT 100 resistance, bridge inputs etc.). Additional 4 digital inputs / outputs available for signal monitoring, resp. controlling tasks. After measurement (up to 16 Bit resolution), linearisation and scaling the individual signal is transmitted via an RS 485 fieldbus interface. Local intelligence enables the ISM 111 to perform complex mathematical and logic functions using both measured inputs and internally calculated variables. The ISM 111 supports industrial standard protocols Profibus-DP, Modbus-RTU and ASCII (special). The module is suitable for standard rail mounting
|
Zoom | Type-No.: 1040.2000
Intelligent Sensor Module, ISM 112
Multi-channel module with 4 analog inputs suitable for measuring current, voltage and resistance (also for thermocouples, PT 100 resistance, bridge inputs etc.). Additional 2 digital inputs / outputs available for signal monitoring, resp. controlling tasks. After measurement (up to 16 Bit resolution), linearisation and scaling the individual signal is transmitted via an RS 485 fieldbus interface. Local intelligence enables the ISM 112 to perform complex mathematical and logic functions using both measured inputs and internally calculated variables. Further, the ISM 112 is equipped with an analog current output, also usable as PID controller. The ISM 112 supports industrial standard protocols Profibus-DP, Modbus-RTU and ASCII (special). The module is suitable for standard rail mounting.
|
Zoom | Type-No.: 1041.0000
Intelligent Interface-Converter, ISK 100
Universal desk top RS-232 / RS-485 Interface-Converter with automatic baudrate-detection. Galvanic isolation protects connected devices from transients up to 1.5 kV. An 18 W power supply for additional up to 6 ISM series modules is built-in.
|
Zoom | Type-No.: 1041.1000
Intelligent Interface-Converter, ISK 101
Universal RS 232 / RS 485 Interface-Converter, integrated in a standard DB09 case. The ISK 101 covers an automatic baud rate selection as well as selection of signal direction. Built-in LED’s indicate the actual status. Supply is achieved via the fieldbus
|
Zoom | Type-No.: 1041.2000
Intelligent Repeater / Converter, IRK 100
Universal RS 485 Repeater/Converter separates a RS 485 Bus from a second one and extents the RS 485 fieldbus by additional max. 31 modules. Totally 3 repeaters can be cascaded, enabling cable length up to 4.8 km. Isolation from each other and from the network structure enables simple installation and enhances the network’s immunity from noise. The converter IRK 100 enables the conversion of signals from RS 232 into RS 485 and reverse. Galvanic isolation protects the connected computer against transients up to 1.5 kV. The IRK 100 is suitable for standard rail mounting.
|
| Type-No.: 1045.0000
Cold Junction Compensation, 4-pole, ICJ 104
for connecting thermocouples with datalogger COMBILOG
Type-No.: 1045.1000
Bus Connector, ICM 100
for connecting – power supply and fieldbus – of all series 100 modules and datalogger COMBILOG / COMBILOG LT
Type-No.: 1045.2000
Bus Terminator, IBT 100
for correct termination of RS 485 fieldbus
|
Zoom | Type-No.: 1050.0000
e.bloxx A1-1
e.bloxx is a modular measuring system for complex applications in meteorology and hydrology. Most outstanding features are:
Extremely high resolution (19 bit at 1 kHz), wide range of signal/sensor connections. Standardized interfaces allow construction of networks with more than 120 modules. Combination with data concentrator e.gate 01 easily enables complete systems with Ethernet-, FTP- resp. Web- functionality.
Suitable for 35 mm EN50022 standard rail mounting.
Type-No.: 1050.1000
e.bloxx A1-4
with 4 multifunctional analog inputs and 4 digital outputs, incl. RS485 fieldbus interface.
Type-No.: 1050.2000
e.bloxx A1-8
with 8 multifunktional analog inputs and 8 digital outputs, incl. RS485 fieldbus interface.
Type-No.: 1051.0000
e.bloxx D1-1
with 8 digital inputs for status detection or 4 digital inputs for fast count- or frequency measurement, incl. RS485 fieldbus interface.
Type-No.: 1051.1000
e.bloxx D1-4
with 32 digital inputs for status detection or 16 digital inputs for fast count- or frequency measurement, incl. RS485 fieldbus interface
Software for graphic evaluation upon request !
Type-No.: 1052.0000
Intelligent Data-Concentrator, e.gate 01
with PROFIBUS-DP and ETHERNET-TCP/IP interface, for connection of automation systems, incl. 4 x RS485 and RS232 for slave devices. Incl. FTP- and Web-Server Function.
Type-No.: 1055.0000
Cold Junction Compensation, CJC-A1
10 pole terminal for connecting thermocouples with e.bloxx A1-1 and A4.
|
|
techn. Daten
|
| |
|
